Skip to main content

SQM for 1 Gbps Lines With OpenWrt

Pictured Gigabit Switch: TP-Link 8-Port Gigabit Ethernet Switch. Amazon Referral Link: https://amzn.to/3bgOOvo

Pictured Access Point: Ubiquiti Unifi 6 Lite. Official Link: https://store.ui.com/collections/unifi-network-access-points/products/unifi-ap-6-lite

Pictured OpenWrt Device: NanoPi R4S. Official Link: https://www.friendlyarm.com/index.php?route=product/product&product_id=284 can also be found on aliexpress. Aliexpress Link: https://www.aliexpress.com/item/1005001941753177.html?spm=a2g0s.9042311.0.0.57064c4dsBfzcu

1.1 Introduction and Why?

The diagram above demonstrates how you would install a more powerful OpenWrt PC or ARM PC as a router into your network. 

The reason why we would want to do this is so we can stop bufferbloat at higher bandwidths with SQM (Smart Queue Management). Currently consumer routers usually can't push past 350 Mbps with luci-app-sqm on because the SQM algorithm cake, uses a lot of CPU processing power. The only way we can get close to 1 Gbits with SQM is by building our own router.

It is also a lot more reliable and better than consumer routers which try to put the modem, routing, and wireless all in one.

What is Bufferbloat and why stop it?

It is lag or ping spikes in video games or zoom calls that is caused when you or someone else uses up all your bandwidth. It could be torrenting, 4k streaming, bulk downloads, or even a speedtest. The SQM algorithm, which can be installed on OpenWrt, can completely mitigate these pings and ensures low latency even under full load. Overall, you do sacrifice a little max speed 5-10% for guaranteed low latencies.

1.2 What Hardware For The OpenWrt Router?

To be honest, I'm not 100% sure what can handle 1000 Mbps in the real world yet because I don't have a 1000mbps connection.

My current connection is 600Mbps. I used to use a SEEED ODYSSEY - X86J4105 which has a CPU Mark Score of ~3000 and it handled 600Mbps DL with ease. The htop screenshot below tells me it uses at most 37% of my CPU under full load. In theory, we can guess that a CPU mark of 3000 should be able to work for 1000 Mbps connections, if 600 Mbps only uses 37% CPU at most.

TL;DR. It is safe to assume, any desktop PC with a CPU mark of around 3000 or more on cpubenchmark.net can handle SQM at 1000 Mbps.

image-1609966808146.png

Pictured: htop of SEEEd Odyssey X86J4105 PC running OpenWrt

Hardware Option 1: The NanoPi R4S (~$85 with accessories and case)

The predecessor, the R2S was known to handle ingress up to 465 Mbps, egress up to 750 Mbps (Source). This R4S is more powerful with 6 cores and 1GB of RAM. R4S is also a low power device! I consider this the best bang for your money for Gigabit SQM.

My ISP gives me 600Mbps DL and 15Mbps UL. My NanoPi R4S running FriendlyWrt can do SQM with fq_codel at these speeds without any issue. Screenshot below shows a rough idea of CPU usage under ingress (DL) at 600 Mbps.

Installation is easy. You just need to flash a microSD card with friendlyWrt. They have a tutorial here: https://wiki.friendlyarm.com/wiki/index.php/NanoPi_R4S#Install_OS

All you have to do to install is...
1. Plug in a microSD card to your computer.
2. Download rk3399-sd-friendlywrt-5.10-YYYYMMDD.img.zip
3. Get win32diskimager and launch it.
4. On win32diskimager select your image file that you downloaded and select your microSD drive letter. Then flash!
5. After flashing is done eject microSD and unplug.
6. Plug in microSD into NanoPi R4S.
7. Hook up WAN to your modem. Hook up LAN to either your switch which connects to a computer or hook up LAN directly to your computer.
8. Power on. Wait about 3 minutes.
9. On the computer that is connected to the switch or NanoPi's LAN port. Go to web browser and enter in http://192.168.2.1 to access your router.

That's it! All that is left is to configure SQM with fq_codel as shown here. There's no need to install luci-app-sqm because the FriendlyWrt image has everything already!

If you're interested in trying the OpenWrt Version this may be of interest to you: https://github.com/quintus-lab/OpenWRT-Rockchip

image-1612828359169.png

Pictured: htop of the 6 core NanoPi R4S with SQM on under speedtest of 600Mbps

 

Hardware Option 2: x86 Desktop

Disadvantage of a regular desktop is power usage... Should you decide to use a PC there are a couple requirements.

1. Make sure it has two Gigabit Ethernet ports. If it has one already, you can add a second one with a Mini PCI-E Gigabit Network Adapter. (Amazon referral link).

2. You also want to make sure it has a CPU Mark of 3000 or more. You can check here: https://www.cpubenchmark.net/cpu_list.php

3. Preferably it would be a low power device around < 25 Watts.

As for installation of software. OpenWrt has their own written guide here: https://openwrt.org/docs/guide-user/installation/openwrt_x86

4. After OpenWrt is setup and running you just need to enable SQM like so: https://www.stoplagging.com/openwrt-method-fq_codel-cake/

Hardware Option 2.1: Seed Odyssey x86 Mini PC (~$250-$300)

Should you decide to go with the pricey Seed Odyssey they did a write up about running OpenWrt on it thru a USB device: https://wiki.seeedstudio.com/ODYSSEY-X86J4105-Installing-openwrt/

Personally I ran mine on a 16GB M.2 SATA SSD since NVME isn't current supported in the base x86 OpenWrt Image. Instead of flashing a USB drive as instructed by SEEED. I flashed my M.2 SATA drive with balenaEtcher instead.

My current connection is 600Mbps. On the SEEED ODYSSEY - X86J4105 which has a CPU Mark Score of ~3000 and it handles 600Mbps DL with ease. The htop screenshot below tells me it uses at most 37% of my CPU under full load. In theory, we can guess that a CPU mark of 3000 should be able to work for 1000 Mbps connections, if 600 Mbps only uses 37% CPU at most.

image-1609966808146.png

Pictured: Seed Odyssey CPU Usage under load at 600Mbps Download

1.3 What Access Point?

I keep hearing raving reviews about the Ubiquiti APs and use one myself. I have extremely stable WiFi with these and never have to reboot them. Ubiquiti also advertises up to 200 concurrent users as well! If you have a recommendation better than these I'd like to know.

Official Link: https://store.ui.com/collections/unifi-network-access-points/products/unifi-ap-6-lite (As of 2/24/2021 free shipping over $100. To get over $100 you can add a filler item.

If you plan on only having one Ubiquti AP I recommend installing via the phone so you don't have to bother with more complicated things like AP Controllers.

If you're on a budget and can't buy a dedicated AP. You can try turning your old router into an access point by putting it into AP mode instead of routing mode. This is important because you should be letting the OpenWrt device do the routing to prevent bufferbloat not your old router.

Facts about WiFi

If you need more coverage you should get more APs not one single AP with a bunch of antennas, because those are marketing gimmicks.

WiFi has limited range due to the physics of their frequency bands.

5Ghz can handle more bandwidth, but will usually be about half the range of 2.4Ghz.

1.4 Contact

If you need help or consultation please join my rocket.chat server at https://chat.stoplagging.com/invite/zaMu6X you can message me @Starfroz by looking me up under the globe icon after registering and logging in.

image-1609968043493.png